Banjo Hangout Logo
Banjo Hangout Logo

Premier Sponsors


Page: 1  2   Last Page (2) 

Oct 30, 2026 - 5:13:03 PM
like this
82727 posts since 5/9/2007

While going over everything the other day I happened to tap my lower co-ordinator rod and got a distinctive
Bb note with sustain (the original one rod from Gibson) and then tapped the Cox 2nd rod and got a C with some sustain,too.
Nearly bell-like,I wanted to remove or somehow reduce their contribution in what was going on inside the resonator.
I took a 10" long piece of duct tape and found it to be just the right width for reaching both rods.
I got it fairly tight top to bottom and found that I could still hear the Bb and C notes when I tapped,but the sustain was gone.
I then set my head a little flat of A instead of right on G# or A.

I notice a purer note,now.
The notes seem to own the whole air-space and aren't sharing it.

Oct 30, 2026 - 5:44:19 PM
like this

5856 posts since 11/20/2004

I am guessing you have brass rods. If so, try a set of steel. I found several years ago that I prefer them for a cleaner sound. I have made my own several times and I am sure you could as well.

Oct 31, 2026 - 6:46:30 AM

82727 posts since 5/9/2007

The bottom (Bb) rod is 1929 Gibson.
I do believe Jimmy used brass rods,but both rods have a ringing duration when tapped...just different notes.

Edited by - steve davis on 10/31/2026 06:47:08

Oct 31, 2026 - 7:18:01 AM

82727 posts since 5/9/2007

I've always liked the great tone/voice of this banjo (Cox 2 conversion) and just wondered what would happen if I canceled out those rod's contributions to the sound.
I would think a steel rod would have a sustained note when tapped.

Oct 31, 2026 - 8:19:32 AM
likes this

BTuno

USA

985 posts since 3/3/2007

Steve, please explain in more detail how you used the duct tape.

Oct 31, 2026 - 10:54:04 AM
likes this

192 posts since 6/30/2020

I might want to try this out. I wonder if I can find a piece of rubber tubing with a slightly smaller diameter than the rods. It could be cut lengthwise and put over the rods

Oct 31, 2026 - 11:32:42 AM
likes this

Owen

Canada

20041 posts since 6/5/2011

I have no knowledge of such ^^ matters.

Would an elastic band [or two?] ... one loop around both rods be worth considering/trying?

Oct 31, 2026 - 3:06:57 PM

82727 posts since 5/9/2007

quote:
Originally posted by BTuno

Steve, please explain in more detail how you used the duct tape.


Sure,Bruce.

My roll of extra heavy duct tape is 1 3/4" wide.

co-rods are 1 1/4" apart,center to center.

10" piece of tape following the rods from the tailpiece to the neck end of the rods making it look like a windmill blade.

Tape the rod closest to the head first with one edge of the tape,then starting in the middle pull the tape tight and stick it to the other rod.Working out from there keep pulling tension and sticking the tape to the other rod.

I left it at one piece so I can try sticking other shapes to the tape.

When I recorded at the Hearst Studio in Camden I was taken by their use of moveable panels/walls within the space and this may turn into a micro version of that.

Edited by - steve davis on 10/31/2026 15:08:29

Oct 31, 2026 - 3:14:05 PM

82727 posts since 5/9/2007

Make that a 9" piece of tape.Inside diameter of the rim.

Oct 31, 2026 - 3:29:38 PM

82727 posts since 5/9/2007

There are many ways to dampen the "voices" of those 2 rods,Owen.
I don't think one rubber band would "shut them up",but I haven't tried that so I should say try whatever you think of,Owen.The amount of deadening can surely be adjusted and then the final test is did I make a difference or am I just kidding myself?
I want to maybe stick a piece of 1" cedar along the tape,but I want to get used to it as is for a week or so.
Trying not change more than one thing at a time.Might get confusing.

Tubing should work fine,Louie.

Edited by - steve davis on 10/31/2026 15:34:03

Oct 31, 2026 - 5:22:43 PM
likes this

4758 posts since 7/12/2006

Hey steve i wonder if you took foam pipe insulation and cut a slit in it then wrapped it around each rod. ( i should probably have my head examined)

Nov 1, 2026 - 5:50:55 AM

82727 posts since 5/9/2007

That "sounds" fine,Gary.
Anything that shuts off the inherent ringing sustain of those rods.
I'm taking this mess to our Sail,Power and Steam Museum Jam today.3 hour jam spread out in a 40' room.Musicians sit around the outside edge with a 20ish audience in the middle.

This will thoroughly test this banjo's projection and tone with the muted rods.

And,the pipe insulation I've used was already slit.

Edited by - steve davis on 11/01/2026 05:53:34

Nov 1, 2026 - 6:05:08 AM
likes this

martyjoe

Ireland

1025 posts since 3/24/2020

That’s a very interesting format for a jam.

Nov 1, 2026 - 6:43:43 AM

82727 posts since 5/9/2007

I go to up to 4 jams per week and this is the only one set up in this way.
There is also a main stage underneath a 10 foot long model of windjammer "The Adventure" which is mounted on the wall,behind.

When I started going to this jam over ten years ago I would at times think of bringing up reconfiguring to musicians in the center surrounded by audience,but I've gotten used to this way and have found this set-up to be more conducive to audience participation during Sleep With One Eye Open,Fox On the Run or Leaving On That New River Train.

Nov 1, 2026 - 7:18:27 AM

82727 posts since 5/9/2007

I just got done checking my rods with a magnet.
The original "2" rod is steel and the upper Cox rod is brass.
The original steel rod taps at Bb and has a ringing note of about the same duration as the upper brass Cox rod which rings at C when tapped.

Both rods after taping sound the same Bb and C notes when tapped,but the lingering duration of those notes is gone.

Nov 1, 2026 - 7:29:59 AM

6012 posts since 9/12/2016

on the construction job--from time to time--some would buy a new hammer that would ring==(resonate) -but identical hammers did not--I would guess that all steel rods have a resonant tone--which supposedly is the wave swinging around on the end and heading back--

Nov 1, 2026 - 8:14:55 AM

Owen

Canada

20041 posts since 6/5/2011

Geez Tom ... now ya tells me!!   

Several decades back I worked on a construction crew ... used to regularly sing Irish Rovers songs while we worked .... led by the owner/boss.    Kinda a bummer that now I can only speculate how much ^^ could have added to our "performances."   sad

[Still not overly happy that a co-worker knocked my good Estwing into the Winnipeg River, but, "eventually" ....  .wink]

Nov 2, 2026 - 7:10:33 AM
likes this

82727 posts since 5/9/2007

I was very pleased with the overall performance of this banjo at yesterday's SPS jam.

So hard to put words to sounds,but the notes seemed "drier" but not restricted.
Searching for words...

More focused on each note.
Maybe more "pop" on each note with less encroachment from the surrounding notes?
More focus on the "bass" notes.
Different "balance" between lows and highs favoring the lows.

That's a pretty good description of my first impressions.
I like it and plan on leaving it as is for a good month.

I love the flexibility of the banjo's construction.
We get to play around with every piece of it.

Nov 2, 2026 - 7:25:20 AM

6012 posts since 9/12/2016

in the science realm of this--notes on a wave can enhance each other if they go back and forth in unison-the peak of one wave hits at the same the peak of the other hits---if the peak of one hits with the trough of the other it weakens it's opponent but in this case --volume still rules
my 2 cents

Nov 2, 2026 - 7:27:32 AM

6012 posts since 9/12/2016

btw Owen Estwings ruled here for a few years--I always liked my'' Easy swing ''all their sizes

Edited by - Tractor1 on 11/02/2026 07:29:04

Nov 2, 2026 - 8:21:23 AM

82727 posts since 5/9/2007

I have a 20 oz. Estwing.
The guys in my old band are 3 pro carpenters and a pro plumber.They know their stuff and they all said when I started building my own house:
"Don't get on a roof with a wooden handled or curved claw hammer.It has to be straight clawed and one solid piece of steel.
You might need to save a potential fall by driving the claws down through the roofing and into the plywood,below.And the flexible handle coating needs to be in good shape and not taped."

I use my Bostich air-nailer for the most part,these days.I promised my friends I wouldn't get on a roof,anymore.

Edited by - steve davis on 11/02/2026 08:23:36

Nov 2, 2026 - 9:01:49 AM

Owen

Canada

20041 posts since 6/5/2011

I'm extra careful when I'm on a roof nowadays* and never more than bungalow height... I think IF I did slip/trip I'd be "break dancing" [maybe in double-time] from that point until I hit the ground. sad

* getting the ladder out and set up is sometimes the most strenuous part. 

Nov 3, 2026 - 5:04:09 AM
likes this

82727 posts since 5/9/2007

One of my favorites is today's Camden American Legion Jam.
Jam from 4:30 to 5:30/open mic 5:30 to 7.
Good song writers around here singing about living around here.

Nov 7, 2026 - 5:07:23 PM
likes this

82727 posts since 5/9/2007

It's a subtle yet strong difference at the jams.
Sunday will be the big room at the Steam Museum.
It was fine at Thursday's Schoolhouse Jam.I really like the balance with the other instruments and the tone.
Phat notes.

Nov 8, 2026 - 10:49:47 AM

45979 posts since 3/5/2008

I am...only wondering..if that tape deflects air movement..(which is sound)..

N that makes or contributes to the change..

Nov 13, 2026 - 12:11:18 PM

82727 posts since 5/9/2007

It certainly would affect air movement,Al.
There was a breather hole in my snare drums and they made a definite "puff" when striking the head.
A plucked note on a stretched membrane should also pump air,albeit on a finer level.

A few pieces of string cinched around the 2 rods would dull the ringing duration of the rods and still let air flow freely.
The earlier suggestion of pipe covers would be another way of affecting the rods' contribution to the sound without affecting the air movement as fully..

Another way to test the rods' contributions to tone would be to clip on 2 or 3 of those big plastic clips used to close potato chip bags.
I'm going to try the clips on my Bob French maple banjo.
I've always preferred a mahogany or walnut neck and find maple to be a bit punchier/cutting than I like.

Edited by - steve davis on 11/13/2026 12:12:41

Page: 1  2   Last Page (2) 

Terms of Use | Privacy Policy | Privacy Consent (EU/GDPR Only)

Copyright 2026 Banjo Hangout. All Rights Reserved.





Hangout Network Help

View All Topics  |  View Categories

0.3476563